Newport-brass 1-617 Manual do Utilizador descarregar pdf

2 & 3 Port In Wall Diverter

Installation Instructions for Model No. 1-617, 1-618

Recommended Installation by a Professional Plumbing Contractor

NOTE: Use Teflon tape or equivalent to seal all threaded port joints.

Warning: To prevent severe damage to valve body, any solder/braze process must be performed a min. of 4” from ports, otherwise

cartridge must be removed from valve body.

1. Valve supplied in 3-way mode; 2-way Washer supplied seperately.

2. To change to 2-way mode, remove All-thread, Stem and Diverter Nut. See Figure 1. Otherwise proceed to step 4.

Select the appropriate 2 or 3-way Washer and orientation for your application, per Diagram 2a, 2b or 2c, and place onto cartridge.

2a or 2b. 2-wa

is used for 2 end devices, a 1/2 NPT Cap (not included), is required on the unused “OUT” port. Connect end

device lines to “OUT” ports 1 & 2 or 1 & 3. Unused “OUT” port C

AN NOT be used as shut off.

2c. 3-wa

y is used for 3 end devices. Connect end device lines to “OUT” ports 1, 2 & 3.

3. Re-assemble Diverter Nut, Stem and All-thread.

4. Diverter is used with a mixed (hot & cold) input, (ie Balance Pressure or Thermo Valve), connect supply to “IN” port only.

5. Connect end devices to “OUT” ports

6. Install Escutcheon/Bonnet trim and mark the All-thread nipple were excess needs to be

trimmed.

7. Remove Escutcheon/Bonnet trim and cut All-thread nipple 1/16” less than indicated mark

to prevent exposure of nipple threads.

Note: Do not cut Stem and All-thread nipple until finished wall is complete and dimension

check of Handle and Escutcheons/Bonnet trim is done. (Stem groove @ ½” intervals.)

8. Cut Cartridge Stem at least ½” past the end of the cut All-thread nipple.

Final Stem length may vary based on individual Handle Base insertion.

9. Reinstall Escutcheon/Bonnet trim and Handle.

10. Secure Handle into place.

11.Turn on water supply.

Note: To achieve desired Handle rotational alignment, the handle MUST be removed from

Diverter body and repositioned on the Cartridge Stem.

3 OUTLET

1/2” NPT (ext.)

1/2” Sweat (int.)

1 Mixed INLET

1/2” NPT (ext.)

1/2” Sweat (int.)

Cap

(not included)

Figure 1

1-617-2 Spare Parts Kit

(Also includes (1) 20 Tooth

Stem for 1-618)

6-3/8”

1/2”

16 tooth brch: model 1-617

20 tooth brch: model 1-618

9/16-20

1-9/16”

7/8”

O-ring

All thread

Stem

2-Way

Washer

3-Way

Washer

Diverter Nut

Cartridge

Body

1 2

Resumo do Conteúdo

Página 1 - Figure 1

2 & 3 Port In Wall DiverterInstallation Instructions for Model No. 1-617, 1-618Recommended Installation by a Professional Plumbing ContractorNOTE:

Página 2 - (949)417-5207

(949)417-5207NWP-1-617a Santa Ana, CA 92704

Comentários a estes Manuais

Sem comentários

Newport-brass 1-617 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para a casa Newport-brass 1-617. Newport Brass 1-617 User Manual [en] Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Para a casa Newport-brass 1-617